Multiple Choice Identify the
choice that best completes the statement or answers the question.
|
|
1.
|
You are pulling feeder cables
to a MUTOA through a fire wall, what are the requirements?
a. | Cut a hole just big enough for the
cable | c. | Cut a 3” hole and fire caulk
| b. | Cut a 2” hole and fire
caulk | d. | Check the requirements for that rated
wall
|
|
|
2.
|
What is the typical AWG size
for a series 6 center conductor?
a. | 18 AWG | c. | 22 AWG | b. | 16 AWG | d. | 14 AWG |
|
|
3.
|
Adjusting a room acoustically,
you would use ______ noise.
a. | Pink | c. | Music | b. | White | d. | intermittent |
|
|
4.
|
What is the 1st step when
certifying a data link?
a. | Calculate wire
length | c. | Wire
map | b. | Determine wire type | d. | Calibrate testers |
|
|
5.
|
What is a Wiegand
reader?
a. | A type of bar code
reader | c. | A specific format used in card
readers | b. | A high speed optical reader | d. | A device used with wireless access point to verify data
integrity |
|
|
6.
|
Measurement of AC resistance is
called?
a. | Ohms | c. | Impedance | b. | Mhos | d. | None of the above |
|
|
7.
|
Which is the general formula
for electric power?
a. | P= I x
R | c. | P=V / R
| b. | P= I x
E | d. | P= I / R |
|
|
8.
|
Category 5 cables exhibit
________ attenuation than category 3 cables.
|
|
9.
|
The nominal voltage supplied
from the telephone company on public telephone lines(except during ringing) is
________.
a. | 24 VDC | c. | 120 VAC | b. | 48 VDC | d. | 48 VAC |
|
|
10.
|
In a typical wiring, the
blue-white pair is used for:
a. | Control
functions | c. | Bridging | b. | Tip & Ring | d. | None of these |
|
|
11.
|
Where do you use bridging
clips?
a. | An
RJ-31X | c. | Telephone switching
system | b. | A 66 block | d. | Across Tip & Ring line |
|
|
12.
|
A ______ modular jack contains
connection points for two telephone pairs.
|
|
13.
|
__________ was devised so that
a transmission path can carry many telephone conversations at the same time.
a. | Dial
tone | c. | Tip/ring | b. | Asynchronous transmission | d. | Multiplexing |
|
|
14.
|
Proper respirator fit may be
prevented by:
a. | A person’s physical face
structure | c. | Excessive facial
hair | b. | Glasses with temple pieces | d. | All the above |
|
|
15.
|
Choose the item(s) required to
make a simple CCTV system work.
a. | camera and
lens | c. | monitor | b. | cable | d. | all the
above |
|
|
16.
|
Loose tube type fiber cable is:
a. | Usually used
outside | c. | May require a
“break out kit” | b. | Made to allow for expansion and contraction as temperatures
change | d. | All of these |
|
|
17.
|
Choose the method(s) indoor
pan/tilt platforms can be mounted.
a. | bracket
mounting | c. | below the
ceiling | b. | ceiling mounted | d. | all of these |
|
|
18.
|
The cathode end of a diode is
often marked with:
a. | a bright
color | c. | the letter
“C” | b. | a band | d. | a red
dot |
|
|
19.
|
According to the NEC, metal
cable trays and wire ways ________ bonded to ground.
a. | shall not
be | c. | will
be | b. | shall
be | d. | will not be |
|
|
20.
|
What is the energy limitation
for a CATV system as qualified by the NEC?
a. | 24 VAC | c. | 60 Volts | b. | 12 VAC | d. | 12 VDC |
|
|
21.
|
Which of the following optical
fiber cables are permitted to be installed in cable trays?
a. | OFCP | c. | OFN | b. | OFCR | d. | all of these |
|
|
22.
|
The main cause of job-related
eye injuries is:
a. | Electrical
hazards | c. | Dust or
powders | b. | Lasers | d. | Flying objects or
particles |
|
|
23.
|
Which of the following best
describes the term “transceiver”?
a. | Electronics to support transmitting
and receiving | c. | Electronics to
stop overheating | b. | Electronics to prevent feedback | d. | Receiver |
|
|
24.
|
Near end Crosstalk (N.E.X.T)
is:
a. | Desirable in almost every
installation | c. | Undesired
induction of a signal from one pair to another | b. | Needed for the digital network to work
flawlessly | d. | Measured at the far end of the cable
for best results |
|
|
25.
|
What is the proper way to
ascend and descend a ladder?
a. | facing
away | c. | facing
towards | b. | carrying material | d. | both b & c |
|
|
26.
|
Anti-passback is a feature
normally found in which type of system?
a. | Sound
system | c. | Access
system | b. | Burglar alarm system | d. | CCTV system |
|
|
27.
|
An LED can be designed to
emit:
a. | visible light or infrared
light | c. | only infrared
light | b. | only visible light | d. | visible light or ultraviolet
light |
|
|
28.
|
Choose the type(s) of device(s)
for electronic decisions.
a. | detection
device | c. | action
device | b. | management device | d. | all of these |
|
|
29.
|
The unit used to specify the
amount of resistance in a circuit is the:
a. | Volt | c. | Ampere | b. | Ohm | d. | Coulomb |
|
|
30.
|
When using 24-volts AC to power
CCTV equipment, you would use a __________ transformer.
a. | class 1 | c. | rectifying | b. | class 2 | d. | step-up |
|
|
31.
|
What is it called when data is
transmitted in both directions simultaneously?
a. | full-duplex
communication | c. | time-division
multiplexing | b. | half-duplex communication | d. | two-way multiplexing |
|
|
32.
|
Loudspeakers that operate below
300 Hz only are called ______.
a. | midrange | c. | super-tweeter loudspeakers | b. | subwoofers | d. | tweeters |
|
|
33.
|
The purpose of a block diagram
is to present the _______ of the equipment in a simple, readily accessible form.
a. | current
flow | c. | measurement
process | b. | logical structure | d. | wiring diagram |
|
|
34.
|
The nominal voltages supplied
by telephone companies in the United States are _______ volts for voice circuits and _____ volts for
ringing circuits.
a. | 12 / 24 | c. | 48 / 90 | b. | 24 / 48 | d. | 50 / 100 |
|
|
35.
|
A(n) _________ combines
multiple signals, provides input selection, and allows signal control.
a. | amplifier | c. | mixer | b. | equalizer | d. | transformer |
|
|
36.
|
What is the best way to protect
against voltage spikes in a DC circuit?
a. | add a capacitor across the
contacts | c. | use an in-line
fuse on the common wire of the contact | b. | add a diode across the relay coil | d. | use an isolation transformer |
|
|
37.
|
The maximum recommend length
for a single-section ladder is ______ feet.
|
|
38.
|
_______ are the most common
shock-related injury.
a. | Amputations | c. | Burns | b. | Broken bones | d. | Falls |
|
|
39.
|
Which article in the National
Electrical Code would you reference to answer a question about Grounding?
a. | Article
90 | c. | Article
250 | b. | Article 100 | d. | Article 500 |
|
|
40.
|
________ and _______ are the
two types of delay measured in a cable test.
a. | Delay skew/
NVP | c. | Propagation delay/ Delay
skew | b. | NVP/ return loss | d. | Propagation delay/ NVP |
|
|
41.
|
How should tools and material
be transferred to your partner when working on a scaffold?
a. | accurately
tossed | c. | not at
all | b. | slid along the walk board | d. | carefully passed |
|
|
42.
|
The _______ is the unit of area
used to measure the cross sectional area of wire.
a. | circular
inch | c. | square
inch | b. | circular mil | d. | square mil |
|
|
43.
|
Convert the following value-
212 mA = _______ amps
a. | 0.000212 | c. | 0.212 | b. | 0.0212 | d. | 212 |
|
|
44.
|
Which type of voltage can be
tested using a solenoid-type voltage tester?
a. | AC
voltage | c. | battery
voltage | b. | AC and DC voltage | d. | DC voltage |
|
|
45.
|
Chapter 8 of the NEC covers
___________ systems and is not subject to the requirements of the other chapters except where they
are specifically referenced therein.
a. | communications | c. | grounding | b. | computer | d. | definitions |
|
|
46.
|
A force that pushes electrons
through a circuit is called _________.
a. | resistance | c. | power | b. | current | d. | voltage |
|
|
47.
|
Which article in the National
Electrical Code would you reference to find the DEFINITION for a signaling circuit?
|
|
48.
|
Convert 0.2 amps to
milliamps.
a. | 0.0002
mA | c. | 200
mA | b. | 20
mA | d. | 2000 mA |
|
|
49.
|
When power sources are
connected in series, the total voltage is equal to the ______ of the individual
voltages.
a. | average | c. | highest | b. | difference | d. | sum |
|
|
50.
|
The total power consumed in a
parallel circuit is _________ the power consumed in each branch.
a. | always less
than | c. | the reciprocal
of | b. | the product
of | d. | the sum of |
|