Multiple Choice Identify the
choice that best completes the statement or answers the question.
|
|
1.
|
If you have a return air
ceiling what kind of cable would you install?
|
|
2.
|
Which test instrument would you
use to test long distance fiber for reflective and non-reflective events?
a. | Optical laser continuity
check | c. | OTDR | b. | Power Meter | d. | LED continuity check |
|
|
3.
|
What is the 3dB
rule?
a. | If the distance to the speakers is
cut by half, the volume is increased by 3dB. | c. | If you add a speaker you must increase the volume 3dB
| b. | If you double the wattage on the
load you increase the volume by only 3dB. | d. | Increasing 3dB triples the power |
|
|
4.
|
What is a Fusion splicer used
for?
a. | Fiber
splicing | c. | Coax
splicing | b. | Copper Data splicing | d. | none of these |
|
|
5.
|
How many connectors would be
required on a face plate if you needed composite(RCA), 2 BNC and stereo speaker
connections?
|
|
6.
|
What is the typical AWG size
for a series 6 center conductor?
a. | 18 AWG | c. | 22 AWG | b. | 16 AWG | d. | 14 AWG |
|
|
7.
|
What is the typical AWG size
for a CAT 5 cable?
a. | 26-24
AWG | c. | 20-18
AWG | b. | 24-22 AWG | d. | 18-16 AWG |
|
|
8.
|
What are CRT’s?
a. | Type of
horn | c. | Type of magnetic
switch | b. | Type of siren | d. | Type of monitor |
|
|
9.
|
What is the unit of measurement
when measuring attenuation loss/gain in a coaxial system?
|
|
10.
|
What does EOL stand
for?
a. | End Of
Line | c. | Error on Line
Set | b. | Error on Line | d. | Both a & c |
|
|
11.
|
If you suspect hazardous dust
is in the area you are working you should __________.
a. | get a mask then continue to work
| c. | leave the area right away and report
to you supervisor | b. | spray the area with water then continue to
work | d. | try and stay as low as
possible |
|
|
12.
|
What cable is an ST connector
used on?
a. | Fiber | c. | 18-2 | b. | Coax | d. | 4pr communication |
|
|
13.
|
Adjusting a room acoustically,
you would use ______ noise.
a. | Pink | c. | Music | b. | White | d. | intermittent |
|
|
14.
|
What is the 1st step when
certifying a data link?
a. | Calculate wire
length | c. | Wire
map | b. | Determine wire type | d. | Calibrate testers |
|
|
15.
|
What does the acronym
“SPL” stand for?
a. | special people
lately | c. | sound pressure
level | b. | spectacular project latencies | d. | step level |
|
|
16.
|
There are ________ pairs in
each binder group of a multi-pair UTP backbone cable
|
|
17.
|
Category 5 cables exhibit
________ attenuation than category 3 cables.
|
|
18.
|
A ______ modular jack contains
connection points for two telephone pairs.
|
|
19.
|
Proper respirator fit may be
prevented by:
a. | A person’s physical face
structure | c. | Excessive facial
hair | b. | Glasses with temple pieces | d. | All the above |
|
|
20.
|
What is the best way to control
excessive bleeding?
a. | By running it under
water | c. | Direct pressure on the
wound | b. | With a loose bandage | d. | Wait to see if it stops |
|
|
21.
|
Low voltage systems are not
capable of electrocution because:
a. | current is to
low | c. | Both A and
B | b. | voltage is to
low | d. | Low voltage systems can cause
electrocution |
|
|
22.
|
When working on ladders, you
should not extend your body beyond the rails, this is commonly called:
a. | the “ladder”
rule | c. | the “arm’s length”
rule | b. | the “belt buckle” rule | d. | the “lean-out” rule |
|
|
23.
|
OSHA requirements for a job
site do not
include:
a. | Coffee and donuts at break
time | c. | Store flammable rags in containers
that have lids | b. | Immediately report unsafe conditions and
accidents | d. | Cleanup construction debris and
scrap regularly |
|
|
24.
|
A series circuit always has
______ current path(s).
|
|
25.
|
The _______ pattern is the
preferred layout for a paging system.
a. | square | c. | diamond | b. | staggered | d. | side by side |
|
|
26.
|
Loose tube type fiber cable is:
a. | Usually used
outside | c. | May require a
“break out kit” | b. | Made to allow for expansion and contraction as temperatures
change | d. | All of these |
|
|
27.
|
In a typical burglar alarm
system, a door contact is configured as:
a. | Normally
open | c. | Shunted | b. | Normally closed | d. | Bipolar |
|
|
28.
|
According to the NEC, metal
cable trays and wire ways ________ bonded to ground.
a. | shall not
be | c. | will
be | b. | shall
be | d. | will not be |
|
|
29.
|
Openings in floors should
be:
a. | guarded | c. | guarded or covered | b. | covered | d. | none of these |
|
|
30.
|
Choose the correct components
of a magnetic lock.
a. | key,
tumbler | c. | coil,
plunger | b. | electromagnet, strike plate | d. | doorknob, deadbolt |
|
|
31.
|
When measuring resistance in
circuit for a professional sound system, one would use a(n)___________.
a. | ammeter | c. | impedance bridge | b. | spectrum analyzer | d. | None of these |
|
|
32.
|
To increase the field of view
of a CCTV camera, a _________ is used.
a. | telephoto
lens | c. | short focal
length | b. | infrared lens | d. | none of these |
|
|
33.
|
In an audio system, an
equalizer is normally installed:
a. | Before the power
amplifier | c. | After the power
amplifier | b. | Before the mixer |
|
|
34.
|
What does OTDR stand
for?
a. | oral tooth decay
rate | c. | option technical Doppler
rate | b. | optical time domain reflectometer | d. | None of these |
|
|
35.
|
A series of digits or
characters that must be entered into a system such as a telephone or other communication terminal to
gain access, is known as______?
a. | prefix | c. | pin number | b. | codec | d. | access code |
|
|
36.
|
What does the format size
determine in a camera?
a. | focal length, focus range and lens
length | c. | lens length, focus range and
weight | b. | focal length, lens size and resolution | d. | resolved length, focus size and camera
length |
|
|
37.
|
What things need to be
considered when installing pan/tilt units?
a. | Is there enough horizontal clearance
for the total movement required? | c. | Will this unit be subject to wind-loading | b. | Is there enough vertical clearance for the total movement
required? | d. | all the
above |
|
|
38.
|
What is the minimum voice
cabling type for a residential application?
a. | 4-pair, Category
2 | c. | 4-pair, Category
5 | b. | 4-pair, Category
3 | d. | 4-wire, station
wire |
|
|
39.
|
What device is used to boost a
weaker audio signal to a level suitable for further mixing and signal
processing?
a. | amplifier | c. | mixer | b. | mixing console | d. | preamplifier |
|
|
40.
|
Which of the following best
describes acoustic feedback?
a. | echo
effect | c. | low pitched
squeal | b. | high pitched squeal | d. | both b and c |
|
|
41.
|
What is the best way to protect
against voltage spikes in a DC circuit?
a. | add a capacitor across the
contacts | c. | use an in-line
fuse on the common wire of the contact | b. | add a diode across the relay coil | d. | use an isolation transformer |
|
|
42.
|
Which of the following best
describes the main reason for connecting computers together?
a. | to reduce the amount of software
needed | c. | to share
resources | b. | to save overhead costs | d. | both a and b |
|
|
43.
|
Decreasing the resistance of a
circuit will cause the _____________.
a. | current to
decrease | c. | voltage to
decrease | b. | current to increase | d. | voltage to increase |
|
|
44.
|
_______ are the most common
shock-related injury.
a. | Amputations | c. | Burns | b. | Broken bones | d. | Falls |
|
|
45.
|
________ and _______ are the
two types of delay measured in a cable test.
a. | Delay skew/
NVP | c. | Propagation delay/ Delay
skew | b. | NVP/ return loss | d. | Propagation delay/ NVP |
|
|
46.
|
A force that pushes electrons
through a circuit is called _________.
a. | resistance | c. | power | b. | current | d. | voltage |
|
|
47.
|
If you decrease the voltage in
a series circuit, the current will ___________.
a. | decrease | c. | increase | b. | double | d. | remain the
same |
|
|
48.
|
Which article in the National
Electrical Code would you reference to find the DEFINITION for a signaling circuit?
|
|
49.
|
The unit of electromotive force
is the _______.
a. | ampere | c. | ohm | b. | volt | d. | watt |
|
|
50.
|
The total power consumed in a
parallel circuit is _________ the power consumed in each branch.
a. | always less
than | c. | the reciprocal
of | b. | the product
of | d. | the sum of |
|